Speciality lubricant solutions for the bakery industry

Dough Mixer

Bearings

Klübersynth UH1 14-151

-Good corrosion protection reduces the risk of premature bearing failure
-Good pumpability in centralized grease system prevents grease starvation
-For a wide service temperature range due to the soft consistency of the grease

Enclosed Gears

Klüberoil 4 UH1 N series

-Higher wear protection
-Better cold start with the same nominal viscosity (ISO VG)
-May not require oil coolers due to reduced temperatures
-Reduced friction leads to lower energy   costs

Proofer

Bearings

Klüberfood NH1 94-402

-Increased component availability and extended maintenance intervals owing to its good load-carrying capacity due to good corrosion protection
-Reduces friction and wear, e.g. in rolling bearings, owing to its good wear protection properties and good flow characteristics.

Chains

Klüberoil 4 UH1- 15 Spray

-NSF H1 registered supporting process reliability
-Good penetrative properties facilitating both quick disassembly of component parts and reduced down-time
-Corrosion protection properties to maximise component life

Freezer

Bearings

Klübersynth UH1 14-31

-Reliable operation at low temperatures due to soft consistency and low base oil viscosity
-Reduced risk of premature component failure due to good adhesion and anticorrosive behaviour
-Lubricant starvation prevented by very good pumpability in centralised lubricating systems
-NSF-H1 registration for higher process reliability

Chains

Klüber Summit HySyn FG 32

-Klüber Summit HySyn FG oils are NSF H1 registered for use in the food-processing and pharmaceutical industry and comply with FDA 21 CFR Sec 178.3570
-ISO 21469 certified – supports compliance with the hygienic requirements of your production.
-Low maintenance and operating costs due to extended oil change intervals up to 4,000 operating hours in oil-injected screw-type compressors
-Easy compressor conversion from mineral to the synthetic Klüber Summit HySyn FG oils due to miscibility and compatibility with common seal materials
-Low tendency to evaporation and thus low impact of the oil vapour on the compressed air
-Long service of oils filters, activated carbon filters and oil separators
-Also suitable for the lubrication of gears due to the high scuffing load capacity
-Used and approved by Aerzener, Air   Liquide, Boge, CompAir, Worthington, Getriebebau Nord, Lenze etc.

Gears

Klüberoil 4 UH1-32 N

-Registered as NSF H1 and certified according to ISO 21469
-High scuffing protection
-Good wear protection for gears and rolling bearings
-Good shear stability for reliable lubricant film formation
-Excellent ageing and oxidation resistance
-Wide service temperature range due to good viscosity-temperature behaviour
-Low foaming tendency
-Energy savings due to optimised friction behaviour good elastomer compatibility
-Approved by numerous gear OEMs

Ovens

Grease Lubricated chains operating at high temperatures

BARRIERTA L 55/2

-Higher machine availability and less need for maintenance
  at very high operating temperatures up to 260 °C
  under the influence of aggressive media and vapours
  when used with plastics and sealing materials

-Reliable operation in numerous industries and component types
  thanks to BARRIERTA base oils, which are made specifically to enable long-term stability
  backed by a large number of approvals and references for various applications
  four consistency classes to suit different applications

Reducing the Total Cost of Operation

Oil-lubricated chains operating at high temperatures

Klüberfood NH1 CH 2-220 Plus

Reduced oil consumption due to lower evaporation losses compared to other ester oils commonly used in high-temperature chain applications in the food-processing industry
Extended chain life through enhanced wear protection, leading to lower life cycle costs
NSF-H1 registration for increased process reliability

Enclosed Gears

Klüberoil 4 UH1 N series

-Higher wear protection
-Better cold start with the same nominal viscosity (ISO VG)
-May not require oil coolers due to reduced temperatures
-Reduced friction leads to lower energy costs